GI-1100 Tin Silicone

Starting at: $160.50

Add to Cart:

Please Choose:

GI-1100 Is a Professional use "Tin" based silicon that can be used for making many different molding projects. The GI-1100 product has a Tensile Strength of 275-PSI and a Shore A Hardness of 10. Excellent for fish reproductions, duck heads, or molds for detailed undercuts!


GI-1100 is an extremely high tear-strength, tin-catalyzed RTV-2 silicone rubber, which was designed for casting epoxy resin and polyester parts. GI-1000 is not sensitive to inhibition, meaning it will cure at room temperature over virtually any surface. It is easy to mix and de-air, and will cure with only a slight degree of shrinkage. The speed at which the rubber hardens can be accelerated with special activators. Condensation cure, two-component silicone rubbers are excellent for most general mold making and prototype applications. GI-1000 is extremely useful for those applications where superior mechanical properties are required.

Extremely high tear-strength: GI-1100 is especially good for molds with deep undercuts and for those molds, which require flexing for part removal.

Low shrinkage: GI-1100 offers exceptional reproduction capability. It is particularly valuable in the production of many-sided molds where exact registrations are required.

Excellent chemical resistance: GI-1100 exhibits extremely long mold life due to unique processing techniques that were developed to meet the rigors of polyester and polyurethane casting.

Low viscosity: The low viscosity of GI-1100 allows for easy mixing and de-airing, ensuring smooth, even flow.

Color-coded catalyst: The blue GI-1000 activator ensures homogeneous mixing and eliminates mold loss resulting from inadequate stirring.

Long pot life: GI-1100 gives good overnight cure despite having a working time of 1.5 /2 two hours. In addition, it is relatively insensitive to temperature and humidity fluctuations.

Insensitive to inhibition: GI-1100 is not inhibited by most common mold-making substrates, eliminating the need to use mold sealers.

Good dielectric properties: GI-1100 provides excellent electrical insulating characteristics over a wide temperature range and is especially suitable for applications where mechanical stresses are involved.

Low cost: GI-1100 has a low specific gravity, which means less of it is required than RTVs with a higher specific gravity. When the long mold life is combined with the low specific gravity, GI-1100 is a cost-effective, high performance RTV silicone rubber.


1. Measure Components

Measure the RTV silicone Base into a disposable container that is approximately four times the volume of the rubber. Accurately add the exact amount of Activator required.

2. Mix Thoroughly

Thoroughly stir the mixture with a flat blade spatula or with mechanical mixing. Be sure to scrape the sides and bottom of the container to ensure the correct ratio of Base to Activator. Stir slowly until a uniform color is achieved without streaks.

3. Degassing Mixture

Place the mixed RTV silicone rubber into a degassing chamber capable of 28 to 29 inches of mercury vacuum. Allow the rubber to expand and collapse back to its original volume. Maintain vacuum for an additional one to two minutes. Release vacuum and remove the container from the degassing chamber.

4. Pour Over Released Pattern

The part to be duplicated should be coated with a mold release agent (MANN -200 is recommended) to ensure easy separation. The part should be placed into a box that will contain the silicone rubber while it is a liquid. Slowly pour the mixed silicone rubber over the released pattern being careful to avoid the formation of air bubbles or entrapped air. Allow the rubber to flow around the part to a minimum depth of 3/8 to 1/2 inch.

5. Allow to Cure

Allow the rubber to vulcanize for 16 to 18 hours at room temperature (70oF). Lower temperatures and/or low humidity will cause the cure time to lengthen; conversely, higher temperatures and/or high humidity will cause the cure time to shorten.

6. De-Mold

Partially disassemble the mold box and remove the cured block of RTV silicone rubber. Carefully flex the mold to remove the original part.

7. Completed Mold with Pattern

The silicone mold is ready to be used with appropriate casting materials to duplicate the original pattern.

Shipping is not included and will be determined by address after shipping.
Always shipped under the guild lines of our fair shipping policy to save you money!

Customers who bought this product also purchased...